HP LaserJet Error Messages A - E



Message on printer display

What it means
What to do
ACCESS DENIED MENUS LOCKED
The control panel function you are trying to use has been locked by the network administrator to prevent unauthorized access.
1. Ask the network administrator to unlock the function. 2. Perform a cold reset. This will reset the printer to factory defaults. If a JetDirect network card is installed it will also reset the IP address and other settings so you might want to remove the JetDirect before performing the cold reset.
BAD DUPLEXER CONNECTION
The duplexer is not correctly installed.
1. Some printers need a right-angle power cord for a duplexer to be installed correctly.   Make sure right-angle cord is installed, if needed. 2. Turn the printer off. 3. Remove and reinstall the duplexer. 4. Turn the printer off and back on. 5. If the message persists, make sure the duplexer is connected and the connector is not damaged. 6. Replace the duplexer.
CHECK INPUT DEVICE alternates with PAPER PATH OPEN PLEASE CLOSE IT
The optional input tray cannot feed print media to the printer because a door or paper guide is open
1. Check the doors and paper guides and close any that are open. 2. If doors and trays are closed, check tabs and sensor levers in the tray for proper operation. Replace any defective tabs or sensors. 3. Replace the PCA controller in the feeder. For 5si, 8000, 8100 series make sure C-link cable is correctly hooked up. Also on the 5si check the paper accessory PCA.
CHECK OUTPUT DEVICE alternates with CLOSE OUTPUT DELIVERY PATH
The optional output device is not properly connected to the printer.
1. Ensure the optional output device is fully seated and properly installed. 2. Check any doors on the output device and verify they are closed.  For 5si, 8000, 8100 series make sure C-link cable is correctly hooked up.
DISK DEVICE FAILURE
The EIO disk had a critical failure or fatal error.
1. Reseat the EIO disk. 2. Remove the EIO disk and replace it with a new one. 3. A bad formatter assembly could also cause this error, replace if needed.
DISK FILE OPERATION FAILED
Requested operation could not be performed (for example, attempting to download a file to a nonexistent directory).
1. Check the file name and the directory name. 2. Reseat the EIO disk. 3. Retry the operation.
DISK IS WRITE PROTECTED
The EIO disk is protected, and no new files can be written to it.
Disable the write protection through HP Resource Manager.
EIO DISK [x] NOT FUNCTIONAL
EIO disk is not working correctly
1. Reseat the EIO disk in slot [X]. 2. Remove and replace the EIO disk in slot [X].
ENV FEEDER LOAD [TYPE] [SIZE]
A job has been sent to the envelope feeder and the feeder is empty, the wrong size is loaded in the feeder, or the type and size are set incorrectly on the control panel.
1. Load the requested envelope type and size into the envelope feeder. 2. Make sure the envelope size and type are set correctly from the paper-handling menu in the printer control panel. 3. Press GO if the desired envelope is already loaded in the feeder. 4. Press -VALUE+ to scroll through other available types and sizes. 5. Press SELECT to accept the alternate type or size.
ENVELOPE FEEDER SIZE = [xxxxx]
The printer is asking what size envelopes have been loaded in the envelope feeder.
In response, you can take either of the following actions: 1. Press SELECT to accept the current envelope size. 2. Press -VALUE+ to change the size and then press SELECT to accept the new size. If you do not press any buttons, the message disappears in about one minute. Note Changing the size here changes the default for the envelopefeeder size in the paper-handling menu.
ENVELOPE FEEDER TYPE = [xxxxx]
The printer has received a job under the following conditions: The envelope type the job requested is not available in the printer. Envelopes have been placed in the envelope feeder (thus triggering the paper sensor).
You can take either of the following actions: 1. Press SELECT to accept the paper type and then press GO. 2. Press +VALUE- to change the type, press SELECT to accept the new type, and then press GO to continue.

Sumber: http://www.printertechs.com

HP LaserJet Error Codes 60 and up



Message on printer display
What it means
What to do
62.X
PRINTER ERROR
There is a problem with the printer memory. The X value refers to the location of the problem: 0 = Internal memory 1 to 4 = DIMM slots 1, 2, 3, or 4
1. Reseat the specified DIMM. 2. Replace the specified DIMM
64
PRINTER ERROR alternates with CYCLE POWER
A scan buffer error occurred
1. Turn the printer off, and then turn the printer on. 2. Perform a cold reset. 3. If the message persists, replace the formatter or firmware DIMM.
66.XX.YY
[TYPE] FAILURE alternates with CHECK CABLES AND CYCLE POWER
An error occurred in an external paper-handling device. 1st X = Device number in chain 2nd X = Device type 1 Input 2 Output 3 Stapler/stacker unit YY = Device specific error
Press GO to clear the message. If the message will not clear: 1. Turn the printer off, and then turn the printer on. 3. Check and reseat all cables between the printer and the specified device. 4. Reseat the external paperhandling device. 5. Replace the unit.  On 5si, 8000, 8100 check the C-link hook up. Also check the external paper handling PCA
68 NVRAM ERROR CHECK SETTINGS
An error occurred in the printer non-volatile memory (NVRAM) and one or more printer settings has been reset to its factory default
1. Print a configuration page and check the printer settings to determine which values have changed. 2. Hold down CANCEL JOB while turning the printer on. This will clean up the NVRAM by removing old areas that are not being used. 3. Replace the formatter.
68.X
PERMANENT STORAGE ERROR alternates with CHECK SETTINGS
An error occurred in the printer’s permanent storage and one or more printer settings has been reset to its factory default.
Print a configuration page and check the printer settings to determine which values have changed.
68.X
PERMANENT STORAGE FULL
The printer’s permanent storage is full. Some settings might have been reset to the factory defaults.
1. Print a configuration page and check the printer settings to determine which values have changed. 2. Hold down CANCEL JOB while turning the printer on. This will clean up the permanent storage by removing old areas that are not being used.
69.X
PRINTER ERROR alternates with CYCLE POWER TO CONTINUE
A temporary printing error occurred. X description: 0 = The duplex mechanism has failed
1. Turn the printer off, and then turn the printer on. 2. Reseat the duplexer. 3. Replace the duplexer
79
SERVICE [XXXX]
The printer detected an error.
1. Press CANCEL JOB to clear the print job from the printer memory. 2. Turn the printer off, and then turn the printer on. 3. Try printing a job from a different software application. If the job prints, go back to the first application and try printing a different file. (If the message only appears with a certain software application or print job, contact the software vendor for assistance.) 4. If the message persists with different software applications and print jobs, disconnect all cables to the printer that connect it to the network or printer. 5. Turn the printer off. 6. Remove all memory DIMMs or third-party DIMMs from the printer. (Do not remove the firmware DIMM in the lowest DIMM slot.) 7. Remove all EIO devices from the printer. 8. Turn the printer on. 9. If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each device. 10. Replace a DIMM or EIO device if you determine that it causes the error. 11. Remember to reconnect all cables that connect the printer to the network or computer. 12. If the error persists, replace the firmware DIMM. 13. Replace the formatter.
79 & 80
errors - general info.
For trouble shooting 79 and 80 errors you want to determine if external I/O devices are the cause or if it is the formatter.
Remove all external I/O devices (JetDirect, memory, etc.) and see if problem persists. If not, replace the formatter.
8X.YYYY EIO [Z] ERROR
The EIO accessory in slot [z] has encountered a critical error. [z] description: 1 = EIO slot 1—The printer detected an error with the EIO accessory. 2 = EIO slot 2—The printer detected an error with the EIO accessory. 6 = EIO slot 1—The EIO accessory detected an error. 7 = EIO slot 2—The EIO accessory detected an error.
1. Turn the printer off, and then turn the printer on. 2. Turn the printer off, reseat the EIO accessory in slot [z], and then turn the printer on. 3. Turn the printer off, remove the EIO accessory from slot [z], install it in a different EIO slot, and turn the printer on. 4. Replace the EIO accessory in slot [z].


Sumber : http://www.printertechs.com




HP LaserJet Error Codes 50-59



Message on printer display
What it means
What to do
50.X
FUSER ERROR
A fuser error has occurred.
1. Turn the printer off, wait 10 minutes, and then turn the printer on. 2. If the message persists, reseat the fuser. If that does not work, replace the fuser. To check the fuser, turn the printer off and remove the fuser. Measure the resistance between the fuser connectors. If it is not within the proper range, replace the fuser. If there is not continuity between the fuser connectors neutral and hot with the fuser removed, replace the fuser. If the problem is not related to the fuser, replace the engine controller board.
50.4
PRINTER ERROR
A problem exists with the customer’s line voltage.
1. Remove the printer from any UPS supplies, additional power supplies, or power strips. 2. Plug the printer into a wall outlet and see if this resolves the problem. 3. If the printer is already plugged into a wall outlet, try another power source in the building that is independent of the one currently being used. 4. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications.
51.X
PRINTER ERROR
A loss of beam-detect occurred. X description: 1 = Beam-detect error 2 = Laser error
1. Press GO. The page containing the error will automatically be reprinted. 2. Turn the printer off and then on. 3. Reseat cables to the laser/ scanner and engine controller. 4. Replace the laser/scanner. 5. Replace the DC controller.
52.X
PRINTER ERROR
The laser scanner speed is incorrect. X description: 1 = Scanner startup error 2 = Scanner rotation error
1. Press GO. The page containing the error will automatically be reprinted. 2. Turn the printer off and then on. 3. Reseat cables to the laser/ scanner and engine controller. 4. Replace the laser/scanner.
53.XY.ZZ
PRINTER ERROR
There is a memory error with an accessory. The DIMM that caused the error will not be used. Values of X, Y, and ZZ are as follows: X = DIMM type 0 = ROM 1 = RAM Y = Device location 0 = internal memory (ROM or RAM) 1 to 4 = DIMM slots 1, 2, 3, or 4 ZZ = Error number 0, 1, 2 = Unsupported o unrecognized memory 3 = Failed RAM test 4, 5 = Exceeded maximum RAM or ROM size 6 = Invalid DIMM speed 7 = DIMM reporting information incorrectly 8 = DIMM RAM parity error 9 = ROM needs to be mapped to an unsupported address 10 = DIMM address conflict 11 = PDC XROM out of bounds 12 = Unable to make a temporary mapping
1. Turn the printer off, and reseat or replace the specified DIMM. 2. Try the DIMM in another slot. (The firmware DIMM must remain in slot #4—the lowest DIMM slot.) 3. Replace the DIMM that caused the error.
54.1
REMOVE SEALING TAPE alternates with FROM TONER CARTRIDGE
The toner cartridge has been installed without removing the sealing tape.
1. Open the top cover and remove the toner cartridge. 2. Pull the sealing tape tab to remove the strip. 3. Reinstall the toner cartridge and close the top cover.
54.4
PRINTER ERROR alternates with CYCLE POWER TO CONTINUE
A problem exists with the customer’s line voltage.
1. Remove the printer from any UPS supplies, additional power supplies, or power strips. 2. Plug the printer into a wall outlet and see if this resolves the problem. 3. If the printer is already plugged into a wall outlet, try another power source in the building that is independent of the one currently being used. 4. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications.
55.xx
PRINTER ERROR alternates with CYCLE POWER TO CONTINUE

An internal communications error occurred.
The page containing the error will automatically be reprinted. 1. Check the power at the customer’s location. 2. Replace the formatter and/or firmware DIMM. 4. Replace the engine controller board. 5. Replace the formatter board.   (On the 5si, 8000, 8100 this could be a fuser problem. Try replacing the fuser.)
56.X
PRINTER ERROR
An incompatible combination of input/ output bins was selected. X = description: 1 = Illegal input or bad accessory connector 2 - Illegal output The page containing the error will automatically be reprinted.
1. Turn the printer off, and then turn the printer on. 2. Check the printer’s configuration. 3. Verify accessory connection.
57.X
PRINTER ERROR
A fan failure was detected. X description: 4 = Printer fan 7 = Duplex fan
1. Check the fan’s connector and make sure the fan is not blocked. 2. Replace the fan. On older style printers this is often caused by a bad main motor. (Older style printer being printers with halogen heating elements in the fuser - 4, 4+, 5, 4si, 5si, etc).
58.2
PRINTER ERROR
An environmental thermistor (TH3) failure occurred.
1. Turn the printer off, and then turn the printer on. 2. Verify the environmental thermistor cable is securely connected. 3. Replace the environmental thermistor. 4. If the error persists, replace the engine controller board.
59.X
PRINTER ERROR
A main motor error occurred. X description: 0 = Motor error 1 = Motor startup error 2 = Motor rotation error
1. Turn the printer off, and then turn the printer on. 2. Check and reseat the fuser and toner cartridge to make sure they are not hindering gear movement in the drive train. 3. Check the main motor’s cable to ensure that it is seated properly. 4. If the error persists, replace the main motor.

Sumber: http://www.printertechs.com