Message on printer display
What it means
What to do
13.XX
Media is jammed at the specified location (and possibly at
other locations). If the message persists after all jams have been cleared, a
sensor or sensor lever might be stuck or broken.
For all jam messages, do the following: 1. Remove jammed print
media from the specified location. Check the entire paper path for other
pieces of media in the path. 2. Open and close the top cover to clear the
message. 3. Check sensors and flags in the paper path for proper operation.
13.0
A non-specific paper jam occurred.
1. Remove jammed media from the specified location. 2. Verify
the paper tray is fully closed. 3. Inspect and/or replace the feed and
separation rollers. 4. Ensure there is no obstruction in the path, such as a
torn piece of paper. 5. Open and close the top cover to clear the message. 6.
Check sensors and flags for proper operation.
13.1
Paper-delay jam at paperfeed area.
1. Ensure that paper trays are loaded and adjusted properly so
media can feed from the tray. It might be necessary to reduce the stack
height of media in the tray. 2. Check the input area for obstructions such as
media in the path. Also check to see if the registration assembly damaged or
unseated. 3. Replace any defective sensors or flags. 4. Verify the media
meets the specifications. 5. Check the pickup feed and separation rollers for
unusual wear. Replace as needed. 6. Rotate the media in the input tray by
180° and/or turn it over
13.10
Jam at duplexer
1. Check the duplexer and the rear area of the printer for
obstructions or damage. 2. Check the duplexer for proper operation. Replace
the duplexer if necessary. 3. Check also fuser and rear diverter assembly for
jamming issues.
13.14
For Laserjet 5si. This error is caused by a defective paper
control PCA
Replace the paper control PCA
13.2
Paper-stopped jam at paper-feed area.
1. Check the input area for obstructions such as paper in the
path. Also check to see if the registration assembly is damaged or if the
transfer roller is out of place. 2. Replace any defective sensors or flags.
3. Ensure the media does not exceed the maximum length. 4. If multiple sheets
are feeding, it might be necessary to fan the media and reduce the stack
height. Also, replace separation pad. 5. Verify that the fuser is properly
installed.
13.20
Media stopped in the paper path during power on or when the
top door was closed.
1. Remove all media in the paper path, and then open and close
the top cover. 2. If the message persists after all media is removed: Check
if media is jammed in the prefeed area. Replace any defective sensors or flags
13.21
The top cover was open while printing
1. Clear the jam and close the top door. 2. If the message
persists, check the top door switch for proper operation.
13.5
Paper-delay jam at fuser.
1. Check the transfer roller and small media belt to ensure
they are operating and can feed print media into the fuser. 2. Check the
paper path for obstructions near the transfer roller, toner cartridge, paper
feed assembly, and fuser. 4. Try removing and reseating the fuser. 5. Examine
the fuser gears and drive gears for wear. 6. If needed replace fuser or
appropriate drive gears, or both. 7. If false error message continues,
replace DC controller.
13.6
Paper-stopped jam at fuser.
1. Check the paper path for obstructions at the fuser and
output/delivery area. 2. Reseat the fuser. 3. Replace any worn drive gears,
defective sensors or flags.
13.99
A non-specific paper jam occurred.
1. Remove jammed media from the specified location. 2. Verify
the paper tray is fully closed. 3. Inspect and/or replace the feed and
separation rollers. 4. Ensure there is no obstruction in the path, such as a
torn piece of paper. 5. Open and close the top cover to clear the message. 6.
Check sensors and flags for proper operation
Message on printer display
What it means
What to do
13.XX
PAPER JAM [LOCATION]
Media is jammed at the specified location (and possibly at
other locations). If the message persists after all jams have been cleared, a
sensor or sensor lever might be stuck or broken.
For all jam messages, do the following: 1. Remove jammed print
media from the specified location. Check the entire paper path for other
pieces of media in the path. 2. Open and close the top cover to clear the
message. 3. Check sensors and flags in the paper path for proper operation.
13.0
PAPER JAM [LOCATION]
A non-specific paper jam occurred.
1. Remove jammed media from the specified location. 2. Verify
the paper tray is fully closed. 3. Inspect and/or replace the feed and
separation rollers. 4. Ensure there is no obstruction in the path, such as a
torn piece of paper. 5. Open and close the top cover to clear the message. 6.
Check sensors and flags for proper operation.
13.1
PAPER JAM OPEN INPUT TRAYS
Paper-delay jam at paperfeed area.
1. Ensure that paper trays are loaded and adjusted properly so
media can feed from the tray. It might be necessary to reduce the stack
height of media in the tray. 2. Check the input area for obstructions such as
media in the path. Also check to see if the registration assembly damaged or
unseated. 3. Replace any defective sensors or flags. 4. Verify the media
meets the specifications. 5. Check the pickup feed and separation rollers for
unusual wear. Replace as needed. 6. Rotate the media in the input tray by
180° and/or turn it over
13.10
PAPER JAM CHECK DUPLEXER
Jam at duplexer
1. Check the duplexer and the rear area of the printer for
obstructions or damage. 2. Check the duplexer for proper operation. Replace
the duplexer if necessary. 3. Check also fuser and rear diverter assembly for
jamming issues.
13.14
For Laserjet 5si. This error is caused by a defective paper
control PCA
Replace the paper control PCA
13.2
PAPER JAM OPEN INPUT TRAYS
Paper-stopped jam at paper-feed area.
1. Check the input area for obstructions such as paper in the
path. Also check to see if the registration assembly is damaged or if the
transfer roller is out of place. 2. Replace any defective sensors or flags.
3. Ensure the media does not exceed the maximum length. 4. If multiple sheets
are feeding, it might be necessary to fan the media and reduce the stack
height. Also, replace separation pad. 5. Verify that the fuser is properly
installed.
13.20
PAPER JAM CHECK REAR DOOR
Media stopped in the paper path during power on or when the
top door was closed.
1. Remove all media in the paper path, and then open and close
the top cover. 2. If the message persists after all media is removed: Check
if media is jammed in the prefeed area. Replace any defective sensors or flags
13.21
DOOR OPEN JAM
The top cover was open while printing
1. Clear the jam and close the top door. 2. If the message
persists, check the top door switch for proper operation.
13.5
PAPER JAM CHECK REAR DOOR
Paper-delay jam at fuser.
1. Check the transfer roller and small media belt to ensure
they are operating and can feed print media into the fuser. 2. Check the
paper path for obstructions near the transfer roller, toner cartridge, paper
feed assembly, and fuser. 4. Try removing and reseating the fuser. 5. Examine
the fuser gears and drive gears for wear. 6. If needed replace fuser or
appropriate drive gears, or both. 7. If false error message continues,
replace DC controller.
13.6
PAPER JAM CHECK REAR DOOR
Paper-stopped jam at fuser.
1. Check the paper path for obstructions at the fuser and
output/delivery area. 2. Reseat the fuser. 3. Replace any worn drive gears,
defective sensors or flags.
13.99
PAPER JAM [LOCATION]
A non-specific paper jam occurred.
1. Remove jammed media from the specified location. 2. Verify
the paper tray is fully closed. 3. Inspect and/or replace the feed and
separation rollers. 4. Ensure there is no obstruction in the path, such as a
torn piece of paper. 5. Open and close the top cover to clear the message. 6.
Check sensors and flags for proper operation
Sumber:http://www.printertechs.com
Tidak ada komentar:
Posting Komentar